Warrior LDG6000 ATS Plug
ATS Panels/Cables
Warrior LDG6000 generator ATS plug
Please refer to your original user manual and wiring diagram when performing connections.
Your Warrior LDG6000 generator should have the following ATS socket (shown below):
Your Warrior LDG6000 generator should have the following ATS socket (shown below):
Other products you might be interested in
Warrior ATS Cable+Plug is used to connect an external ATS panel or/and auto start control module
£42.99
This is an incredibly versatile yet highly
functional thermostat controller. With
this module you can intelligently control
power to most types of electrical device
based on the temperature sensed by the
included high accuracy NTC
temperature sensor. Although this
module has an embedded
microcontroller no programming
knowledge is required. 3 tactile switches
allow for configuring various parameters
including on & off trigger temperatures.
The on board relay can switch up to a
maximum of 240V AC at 5A or 14V DC
at 10A. The current temperature is
displayed in degrees Centigrade via its 3
digit seven segment display and the
current relay state by an on board LED.
functional thermostat controller. With
this module you can intelligently control
power to most types of electrical device
based on the temperature sensed by the
included high accuracy NTC
temperature sensor. Although this
module has an embedded
microcontroller no programming
knowledge is required. 3 tactile switches
allow for configuring various parameters
including on & off trigger temperatures.
The on board relay can switch up to a
maximum of 240V AC at 5A or 14V DC
at 10A. The current temperature is
displayed in degrees Centigrade via its 3
digit seven segment display and the
current relay state by an on board LED.
£39.00
This device allows to start and stop your generator within 17 pre-set time slots throughout the whole week.
Quantity Discount available
£36.00
This device allows to start and stop your appliance within 17 pre-set time slots throughout the whole week.
Quantity Discount available
£34.00
This device allows to start and stop your generator within 17 pre-set time slots throughout the whole week.
Quantity Discount available
£24.00
Charging Battery Type:Lead-acid battery 12V
Plug Type:flat-pin plug or euro type (2 pin plug)
Input Voltage:AC 100~240 V
Output Voltage:13.8 V
Output Current:1000 mA
Other Features:charge for all 12V lead-acid batteries, load sensing output, short circuit protection, comes with 2 crocodile clips
Dimensions: 2.95 in x 1.89 in x 2.17 in (7.5 cm x 4.8 cm x 5.5 cm)
Weight: 3.70 oz (105 g)
Plug Type:flat-pin plug or euro type (2 pin plug)
Input Voltage:AC 100~240 V
Output Voltage:13.8 V
Output Current:1000 mA
Other Features:charge for all 12V lead-acid batteries, load sensing output, short circuit protection, comes with 2 crocodile clips
Dimensions: 2.95 in x 1.89 in x 2.17 in (7.5 cm x 4.8 cm x 5.5 cm)
Weight: 3.70 oz (105 g)
£12.00
40A External power relay
Select this option if your generator or engine doesn't have any slave relays fitted. Many of the generator valves and solenoids have high currents and it may become necessary to “buffer” the control module against harmful currents.
Please select the right quantity of power relays: if you order a basic control module you would possibly need only 2 power relays to operate a starter motor and fuel solenoid. Select 3 power relays if pre-heat control is also included into your order.
Please select the right quantity of power relays: if you order a basic control module you would possibly need only 2 power relays to operate a starter motor and fuel solenoid. Select 3 power relays if pre-heat control is also included into your order.
£3.00